2.4GHz 300Mbps Outdoor WiFi Access Point with inner antenna
- Qualcomm QCA9531 high performance chipset
- High power design with more wireless range
- Support passive PoE/IEEE 802.3af PoE
- ABS waterproof, dustproof and sunscreen shell
- Model:AP80Q-P24
Description:
AP80Q is an 300Mbps high power outdoor CPE/AP with omni antenna; It Comply with IEEE 802.11b/g/n standard, adopt QCA9531 chipset, 16MB flash,64MB SDRAM, 5dBi omni antenna, 500mW high power, more than 200 meters Wi-Fi range, good choice for outdoor Wi-Fi signal coverage.
With AP, Router and Wi-Fi Repeater operation mode, it can transmit Wi-Fi signal in a certain place for outdoor users, or can bridge the exist Wi-Fi signal to extend the range.
AP80 with ABS waterproof, dustproof and sunscreen shell, temperature adaptive and board protective,suit for outdoor Wi-Fi networking projects.
Meantime, it support Power over Ethernet, support passive PoE/IEEE 802.3af PoE, easy in setup even no power socket nearby. With LED light show signal strength, easy to find a suitable place for outdoor CPE, save much human work and cost.
What’s more, AP80 support multi SSID(up to 4), each SSID comply with IEEE 802.1Q VLAN, then AP80 work with our AC controller, easy to be configure and setup centrally, what’s more, it support Portal Certificate, easy to do ads for users.
Main Features:
- Professional outdoor shell design,IP65 dust proof/water proof level. Adopt ABS outdoor engineering plastic shell and industrial components,to provide IP65 level water proof ,dust proof and lightning protection,adapt to wind,sun,thunderstorm,snow and freeze or other adverse environments,even in extreme high and low temperature(-40℃ - +70℃)environment,can work normally and steadily as well.
- With Qualcomm QCA9531 chipset , Flash8MB .DDR 64MB, greatly improved the data processing performance and allow more end users access.
- Independent external power amplifier circuit and low noise amplifier receiving circuit design.
- Long wireless coverage ,transfer all kinds of data smoothly ,do not have any latency. AP80Q is a high power outdoor base station with 160 meters wireless range ,can meet the demands for outdoor wifi project large area coverage , specialize in high power design ,can ensure strong wireless signal and stable performance.
- RF power is adjustable according to the actual use environment .Reduce mutual WIFI interference between each other to improve wireless stability.
- Multiple operation mode to meet the different wireless solutions .
Hardware Spec:
| Hardware: | |||
| Chipset | QCA9531 580MHZ | ||
| Wireless | 802.11N, 2T2R 300M MIMO Technology | ||
| Memory | 64MB DDR2 RAM | ||
| Flash | 16MB | ||
| Interface | 2 10/100 Mbps RJ45 Port, support 12~48V PoE | ||
| 1 Reset Button | |||
| 1 DC Jack, 12V Power Supply | |||
| Antenna | 5dBi omni Antenna | ||
| IP Level | IP65 | ||
| LED Light | POWER WIFI WAN LAN S1(GPIO9) S2(GPIO14) S3(GPIO11) S4(GPIO12) | ||
| Size | L 257mm , W: 87mm, H: 38 mm | ||
| Power | 12V(POE 24V/48V)/1A;110V/220V | ||
| RF Data | |||
| RF Data | 802.11b/g/n: | ||
| 2.4~2.4835GHz | |||
| Korea, Japan, ETSI, FCC | |||
| Modulation | OFDM = BPSK,QPSK, 16-QAM, 64-QAM | ||
| DSSS = DBPSK, DQPSK, CCK | |||
| Data Rate | 300 Mbps | ||
| RF Output Power | <29dBm | ||
| Firmware | |||
| Operation Mode | Gateway/AP/WiFi Repeater | ||
| Protocol/Standard | IEEE 802.3(Ethernet) | ||
| IEEE 802.3u(Fast Ethernet) | |||
| IEEE 802.11b/g/n(2.4G WLAN) | |||
| Wireless | Auto-Channel selection | ||
| Distance Control (802.1x Ack timeout) | |||
| Multiple SSID (4 SSID) | |||
| BSSID | |||
| Security | WEP Encryption-64/128/152 bit | ||
| WPA/WPA2 Personal (WPA-PSK using TKIP or AES) | |||
| WPA/WPA2 Enterprise (WPA-EAP using TKIP) | |||
| Hide SSID | |||
| System Setting | Web-based configuration (HTTP/Telnet) | |
| Firmware upgrade | Upgrade firmware via web browser or TFTP | |
| Administration | Admin Password can be configured | |
| System monitoring | Status in hand , useful statistic and Event log | |
| Log | Supports local logs, logs host, logs file export | |
| Reset | Reset or factory defaults | |
| Backup | Restore settings & configuration of the device to local file | |
| Physical Property | ||
|
Temperature | Working: 0°C~55°C | |
|
| Storage: -20°C to 70°C | |
| Humidity | 5%~95% (typical) | |
